C6owners :: Forums :: C6 Support :: The Garage |
<< Previous thread | Next thread >>
|
suspension errors |
Please Register to enjoy additional Member Benefits |
Author | Post | ||
ststech |
|
||
Joined: Aug 31 2014
Member No: #1845
Location: CREWKERNE somerset |
Getting there slowly brake switch cured numerous faults, but what im getting all the time are these faultsrelating to front static pressure sensor it comes up as one 3 faults then you can clear them and 2 faults remain being front satic pressure sensor and reference hieghts not programmed, Could someone tell me where these sensors are located irc my last c6 had same issue but was at rear State of the ECU: CSS Reference 1 : 627952 Reference 2 : Faults present : 3 C1184 : Reference heights not programmed Characterisation : not characterised Status : Permanent fault Location : Local . Variables associated with the fault battery voltage : 12.04 V Engine speed : 0000 Rpm vehicle speed : 000 kph Front LH stepper motor supply : Present Front RH stepper motor supply : Present Rear LH stepper motor supply : Present Rear RH stepper motor supply : Present ignition on present : present C1165 : Front static pressure sensor signal Characterisation : Open circuit or short circuit to positive Status : Permanent fault Location : Local . Variables associated with the fault battery voltage : 12.04 V Engine speed : 0000 Rpm vehicle speed : 000 kph Front LH stepper motor supply : Present Front RH stepper motor supply : Present Rear LH stepper motor supply : Present Rear RH stepper motor supply : Present ignition on present : present |
||
|
|||
arconell3 |
|
||
Joined: Jun 28 2012
Member No: #922
Location: Kalkar |
Hi there, You'll find the pressure sensor in the front RH wheel bay after removal of the wheel and the splash shield. The other fault indicates that for some reason the reference heights of the cars' suspension were either never set or they've somehow been deleted. In this forums' Technical Documents section under suspension you will find descriptions on removal and refitting of the pressure sensor (may be somebody just pulled off the connector?) and on setting the reference heights. Specifically the last job needs to be done with high precision if you want your C6 to serenely glide the way it was meant to be. PS: If your car has recently been serviced by an official Citroen garage, don't go back there but find a knowledgeable C6 workshop instead. PS2: The battery voltage reading is just a wee bit low at 12.04 V. You may want to check your battery as well. Robert |
||
|
|
||
ststech |
|
||
Joined: Aug 31 2014
Member No: #1845
Location: CREWKERNE somerset |
i have noticed the suspension seems to float up and down a bit too much and it appears to bang and crash over bumps and potholes this is todays reading CSS : Variable damping ECU Response data R61FE55030000056809050604416870090506FE02000001627952 State of the ECU: CSS Reference 1 : 627952 Reference 2 : Faults present : 2 C1165 : Front static pressure sensor signal Characterisation : Open circuit or short circuit to positive Status : Permanent fault Location : Local . Variables associated with the fault battery voltage : 12.06 V Engine speed : 0000 Rpm vehicle speed : 000 kph Front LH stepper motor supply : Present Front RH stepper motor supply : Present Rear LH stepper motor supply : Present Rear RH stepper motor supply : Present ignition on present : present C1166 : Front static pressure sensor signal Characterisation : value inconsistent Status : Permanent fault Location : Local . Variables associated with the fault battery voltage : 14.03 V Engine speed : 1994 Rpm vehicle speed : 008 kph Front LH stepper motor supply : Present Front RH stepper motor supply : Present Rear LH stepper motor supply : Present Rear RH stepper motor supply : Present ignition on present : present |
||
|
|
||
User Colour Key: Head Administrator, Administrator, C6 owner, Technical Expert, C6 Premier Discount Club |